/* ARIA header files for use with ARNL 1.7.1 Copyright(C) 2004, 2005 ActivMedia Robotics, LLC. Copyright(C) 2006, 2007, 2008, 2009 MobileRobots Inc. All rights reserved. This copy of Aria was relicensed for use with Arnl and the Arnl license by MobileRobots Inc. If you wish to download a seperate distribution of Aria licensed under the GPL or a commercial license go to http://www.mobilerobots.com/SOFTWARE/aria.html or contact MobileRobots Inc, at robots@mobilerobots.com or MobileRobots Inc, 10 Columbia Drive, Amherst, NH 03031; 800-639-9481 MobileRobots Inc hereby grants to other individuals or organizations permission to use this software with Arnl and in compliance with the Arnl license. This software may not be distributed to others except by MobileRobots Inc. MobileRobots Inc does not make any representations about the suitability of this software for any purpose. It is provided "as is" without express or implied warranty. */ #ifndef ARCOMMANDS_H #define ARCOMMANDS_H /// A class containing names for most robot microcontroller system commands /** A class with an enum of the commands that can be sent to the robot, see the robot operations manual for more detailed descriptions. */ class ArCommands { public: enum Commands { PULSE = 0, ///< none, keep alive command, so watchdog doesn't trigger OPEN = 1, ///< none, sent after connection to initiate connection CLOSE = 2, ///< none, sent to close the connection to the robot POLLING = 3, ///< string, string that sets sonar polling sequence ENABLE = 4, ///< int, enable (1) or disable (0) motors SETA = 5, ///< int, sets translational accel (+) or decel (-) (mm/sec/sec) SETV = 6, ///< int, sets maximum velocity (mm/sec) SETO = 7, ///< int, resets robots origin back to 0, 0, 0 MOVE = 8, ///< int, translational move (mm) ROTATE = 9, ///< int, set rotational velocity, duplicate of RVEL (deg/sec) SETRV = 10, ///< int, sets the maximum rotational velocity (deg/sec) VEL = 11, ///< int, set the translational velocity (mm/sec) HEAD = 12, ///< int, turn to absolute heading 0-359 (degrees) DHEAD = 13, ///< int, turn relative to current heading (degrees) //DROTATE = 14, does not really exist SAY = 15, /**< string, makes the robot beep. up to 20 pairs of duration (20 ms incrs) and tones (halfcycle) */ JOYINFO = 17, // int, requests joystick packet, 0 to stop, 1 for 1, 2 for continuous CONFIG = 18, ///< int, request configuration packet ENCODER = 19, ///< int, > 0 to request continous stream of packets, 0 to stop RVEL = 21, ///< int, set rotational velocity (deg/sec) DCHEAD = 22, ///< int, colbert relative heading setpoint (degrees) SETRA = 23, ///< int, sets rotational accel(+) or decel(-) (deg/sec) SONAR = 28, ///< int, enable (1) or disable (0) sonar STOP = 29, ///< int, stops the robot DIGOUT = 30, ///< int, sets the digout lines //TIMER = 31, ... no clue about this one VEL2 = 32, /**< int, independent wheel velocities, first 8 bits = right, second 8 bits = left, multiplied by Vel2 divisor. See manual. */ GRIPPER = 33, ///< int, gripper server command, see gripper manual for detail //KICK = 34, um... ADSEL = 35, ///< int, select the port given as argument GRIPPERVAL = 36, ///< p2 gripper server value, see gripper manual for details GRIPPERPACREQUEST = 37, ///< p2 gripper packet request IOREQUEST = 40, ///< request iopackets from p2os PTUPOS = 41, ///< most-sig byte is port number, least-sig byte is pulse width TTY2 = 42, ///< string, send string argument to serial dev connected to aux1 GETAUX = 43, ///< int, requests 1-200 bytes from aux1 serial channel, 0 flush BUMPSTALL = 44, /**< int, stop and register a stall if front (1), rear (2), or both (3) bump rings are triggered, Off (default) is 0 */ TCM2 = 45, ///< TCM2 module commands, see tcm2 manual for details JOYDRIVE = 47, /**< Command to tell p2os to drive with the joystick plugged into the robot */ MOVINGBLINK = 49, ///< int, 1 to blink lamp quickly before moving, 0 not to (for patrolbot) HOSTBAUD = 50, ///< int, set baud rate for host port - 0=9600, 1=19200, 2=38400, 3=57600, 4=115200 AUX1BAUD = 51, ///< int, set baud rate for Aux1 - 0=9600, 1=19200, 2=38400, 3=57600, 4=115200 AUX2BAUD = 52, ///< int, set baud rate for Aux2 - 0=9600, 1=19200, 2=38400, 3=57600, 4=115200 ESTOP = 55, ///< none, emergency stop, overrides decel ESTALL = 56, // ? GYRO = 58, ///< int, set to 1 to enable gyro packets, 0 to disable TTY3 = 66, GETAUX2 = 67, // SRISIM specific: LOADPARAM = 61, ///< @deprecated only supported by SRISim OLDSIM_LOADPARAM = 61, ///< @deprecated only supported by SRISim ENDSIM = 62, ///< @deprecated use SIM_EXIT OLDSIM_EXIT = 62, ///< @deprecated use SIM_EXIT LOADWORLD = 63, ///< @deprecated only supported by SRISim OLDSIM_LOADWORLD = 63, ///< @deprecated only supported by SRISim STEP = 64, ///< @deprecated only supported by SRISim OLDSIM_STEP = 64, ///< @deprecated only supported by SRISim // for calibrating the compass: CALCOMP = 65, ///< int, commands for calibrating compass, see compass manual // SRISIM specific: // SETORIGINX and SETORIGINY overlap with TTY3 and GETAUX2 so they are disabled: //SETSIMORIGINX = 66, //SETSIMORIGINY = 67, //OLDSIM_SETORIGINX = 66, //OLDSIM_SETORIGINY = 67, SETSIMORIGINTH = 68, ///< @deprecated use SIM_SET_POSE OLDSIM_SETORIGINTH = 68, ///< @deprecated use SIM_SET_POSE RESETSIMTOORIGIN = 69, ///< @deprecated use SIM_RESET OLDSIM_RESETTOORIGIN = 69, ///< @deprecated use SIM_RESET // AmigoBot-H8 specific: SOUND = 90, ///< int, AmigoBot (old H8 model) specific, plays sound with given number PLAYLIST = 91, /**< int, AmigoBot (old H8 model) specific, requests name of sound, 0 for all, otherwise for specific sound */ SOUNDTOG = 92, ///< int, AmigoBot (old H8 model) specific, enable(1) or diable(0) sound // Power commands POWER_PC = 95, ///< int, Powers on or off the PC (if the firwmare is set up to do this in its power settings) POWER_LRF = 96, ///< int, Powers on or off the laser (if the firwmare is set up to do this in its power settings) POWER_5V = 97, ///< int, Powers on or off the 5v accessories (if the firwmare is set up to do this in its power settings) POWER_12V = 98, ///< int, Powers on or off the 12v accessories (if the firwmare is set up to do this in its power settings) POWER_24V = 98, ///< int, Powers on or off the 24v accessories (if the firwmare is set up to do this in its power settings) POWER_AUX_PC = 125, ///< int, Powers on or off the auxilliary PC (if the firwmare is set up to do this in its power settings) POWER_TOUCHSCREEN = 126, ///< int, Powers on or off the touchscreen (if the firwmare is set up to do this in its power settings) POWER_PTZ = 127, ///< int, Powers on or off the PTZ (if the firwmare is set up to do this in its power settings) POWER_AUDIO = 128, ///< int, Powers on or off the audio (if the firwmare is set up to do this in its power settings) POWER_LRF2 = 129, ///< int, Powers on or off the second laser (if the firwmare is set up to do this in its power settings) // For SEEKUR or later lateral-capable robots LATVEL = 110, ///< int, sets the lateral velocity (mm) LATACCEL = 113, ///< int, sets the lateral acceleration (+, mm/sec2) or lateral deceleration (-, mm/sec2) SETLATV = 0, ///< int, someday will set the vel // MobileSim specific: SIM_SET_POSE = 224, ///< int4,int4,int4 Move robot to global pose in simulator (does not change odometry). Each value is a 4-byte integer. SIM_RESET= 225, ///< none, Reset robot's state to original in simulator and reset odometry to 0,0,0. SIM_LRF_ENABLE = 230, ///< int, 1 to begin sending packets of data from a simulated laser rangefinder (on the same socket connection), 2 to send extended-information laser packets (with reading flags), 0 to disable LRF SIM_LRF_SET_FOV_START = 231, ///< int Set angle (degrees from center) at which the simulater laser takes its first reading (normally -90). SIM_LRF_SET_FOV_END = 232, ///< int Set angle (degrees from center) at which the simulated laser takes its last reading (normally 90). SIM_LRF_SET_RES = 233, ///< int Set the number of degrees between laser readings (in combination with FOV, determines the number of readings per sweep) (normally 1) SIM_CTRL = 236, ///< int,..., Send a simulator meta-command (an operation on the simulator itself). The initial 2-byte integer argument selects the operation. See simulator documentation. SIM_STAT = 237, ///< none, Request that the simulator reply with a SIMSTAT (0x62) packet. You must have a packet handler registered with ArRobot to receive its output. See simulator documentation. SIM_MESSAGE = 238, ///< string, Display a log message in the simulator. Argument is a length-prefixed ASCII byte string. SIM_EXIT = 239 ///< int, Exit the simulator. Argument is the exit code (use 0 for a "normal" exit). }; }; #endif // ARCOMMANDS_H