# Configurations...
# Comment out the stuff you don't want.
#

# CONFIG_YAFFS_RAM_ENABLED.
# This adds the yaffsram file system support. Nice for testing on x86, but uses 2MB of RAM.
# Don't enable for NAND-based targets.

#USE_RAM_FOR_TEST = -DCONFIG_YAFFS_RAM_ENABLED


# CONFIG_YAFFS_MTD_ENABLED.
# This adds the yaffs file system support for working with a NAND mtd.

USE_MTD = -DCONFIG_YAFFS_MTD_ENABLED

# CONFIG_YAFFS_USE_OLD_MTD
# Enable this to use the old MTD stuff that did not have yaffs support.
# You can use this to get around compilation problems, but the best
# thing to do is to upgrade your MTD support. You will get better speed.

#USE_OLD_MTD = -DCONFIG_YAFFS_USE_OLD_MTD

# CONFIG_YAFFS_USE_NANDECC
# This enables the ECC functions of the generic MTD-NAND driver.
# This will not work if you are using the old mtd.
#
# NB UseNANDECC does not work at present with yaffsram.

USE_NANDECC = -DCONFIG_YAFFS_USE_NANDECC

# CONFIG_YAFFS_ECC_WRONG_ORDER
# This makes yaffs_ecc.c use the same ecc byte order as
# Steven Hill's nand_ecc.c. If not set, then you get the
# same ecc byte order as SmartMedia.

#USE_WRONGECC = -DCONFIG_YAFFS_ECC_WRONG_ORDER

# CONFIG_YAFFS_USE_GENERIC_RW
# Use generic_read/generic_write for reading/writing files. This enables the use of the Linux
# file caching layer.
#
# If you disable this, then caching is disabled and file read/write is direct.

USE_GENERIC_RW = -DCONFIG_YAFFS_USE_GENERIC_RW

# CONFIG_YAFFS_USE_HEADER_FILE_SIZE
# When the flash is scanned, two file sizes are constructed:
# * The size taken from the object header for the file.
# * The size figured out by scanning the data chunks.
# If this option is enabled, then the object header size is used, otherwise the scanned size is used.
# Suggest leaving this disabled.

#USE_HEADER_FILE_SIZE = -DCONFIG_YAFFS_USE_HEADER_FILE_SIZE

#CONFIG_YAFFS_DISABLE_CHUNK_ERASED_CHECK
# Enabling this turns off the test that chunks are erased in flash before writing to them.
# this is safe, since the write verification will fail.
# Suggest enabling the test (ie. keep the following line commented) during development to help debug things.

#IGNORE_CHUNK_ERASED = -DCONFIG_YAFFS_DISABLE_CHUNK_ERASED_CHECK

#CONFIG_YAFFS_DISABLE_WRITE_VERIFY
# I am severely reluctant to provide this config. Disabling the verification is not a good thing to do
# since NAND writes can fail silently.
# Disabling the write verification will cause your teeth to rot, rats to eat your corn and give you split ends.
# You have been warned. ie. Don't uncomment the following line.

#IGNORE_WRITE_VERIFY = -DCONFIG_YAFFS_DISBLE_WRITE_VERIFY

#CONFIG_YAFFS_SHORT_NAMES_IN_RAM
# If this config is set, then short names are stored with the yaffs_Object
# This costs an extra 16 bytes of RAM per object, but makes look-ups faster.

#ENABLE_SHORT_NAMES_IN_RAM = -DCONFIG_SHORT_NAMES_IN_RAM

# End of configuration options.

YAFFS_CONFIGS = $(USE_RAM_FOR_TEST) $(USE_MTD) $(USE_GENERIC_RW) $(USE_HEADER_FILE_SIZE) $(IGNORE_CHUNK_ERASED) $(IGNORE_WRITE_VERIFY) \
                $(ENABLE_SHORT_NAMES_IN_RAM) $(USE_NANDECC) $(USE_OLD_MTD) $(USE_WRONGECC)


EXTRA_CFLAGS += $(YAFFS_CONFIGS) 

O_TARGET := yaffs.o

obj-y = yaffs_fs.o yaffs_guts.o yaffs_ramem.o yaffs_mtdif.o yaffs_ecc.o
obj-m    := $(O_TARGET)

include $(TOPDIR)/Rules.make

